Ubc396t p25
-
- Posts: 106
- Joined: Sun Nov 08, 2009 12:35 am
- Location: sw sydney
Ubc396t p25
Hi all Wife off to St George hospital tomorrow morning for 6 days. Taking scanner with me. Noticed last night when doing a custom search it is not picking up PMR p25 channel any one suggest what I need to check in settings or anything else that might be causing this. My daughter was pulling charger cord out and in of scanner and turning power point on and off while I had it charging. Is it possible it might have a Birdi or corrupted the scanner shold I reset and restore everything back into scanner. It doesn't show Lnk then p25 like it use too.
Thanks sw sydney scanner. Using UBCD396T
Re: Ubc396t p25
Seen a similar issue where it wouldn't pickup any transmissions not just p25 like you.
Make sure broadcast is turned off in options.
Is anything else displayed on the screen while the custom scan is running ?
Make sure broadcast is turned off in options.
Is anything else displayed on the screen while the custom scan is running ?
- rustynswrail
- Posts: 646
- Joined: Thu Mar 11, 2010 10:18 pm
- Location: Blue Mountains
Re: Ubc396t p25
I would do the four finger reset. With the power off, press and hold 2 9 HOLD then turn it ON. Follow the on screen prompts. Reprogram using your software (I hope you are using software) of choice.sw sydney scanner wrote:Hi all Wife off to St George hospital tomorrow morning for 6 days. Taking scanner with me. Noticed last night when doing a custom search it is not picking up PMR p25 channel any one suggest what I need to check in settings or anything else that might be causing this. My daughter was pulling charger cord out and in of scanner and turning power point on and off while I had it charging. Is it possible it might have a Birdi or corrupted the scanner shold I reset and restore everything back into scanner. It doesn't show Lnk then p25 like it use too.
R
Amateur Radio, when all other cures for insomnia fail!
-
- Posts: 106
- Joined: Sun Nov 08, 2009 12:35 am
- Location: sw sydney
Re: Ubc396t p25
Yeh have it save in software, I need to update some anyway probably best option
Thanks sw sydney scanner. Using UBCD396T
Re: Ubc396t p25
Does it say SCR on the screen when running a custom scan ?
-
- Posts: 106
- Joined: Sun Nov 08, 2009 12:35 am
- Location: sw sydney
Re: Ubc396t p25
astro_boy wrote:Does it say SCR on the screen when running a custom scan ?
No. Have all broadcast screen turned off.
CTCSS/DCS SEARCH ON
REPEATER FIND OFF
SET MODULATION AUTO
SET ATTENUATOR OFF
DATA SKIP OFF
ADJUST P25 level AUTO
CLOSE CALL BANDS ON
Thanks sw sydney scanner. Using UBCD396T
-
- Posts: 106
- Joined: Sun Nov 08, 2009 12:35 am
- Location: sw sydney
Re: Ubc396t p25
No. Have all broadcast screen turned off.
CTCSS/DCS SEARCH ON
REPEATER FIND OFF
SET MODULATION AUTO
SET ATTENUATOR OFF
DATA SKIP OFF
ADJUST P25 level AUTO
CLOSE CALL BANDS ON[/quote]
Hi all while doing a bit of updating on computer for the scanner whith the Usad program. I noticed in the general search options under CTCSS/DCS Tone Search!!
( Scanner will not detect or decode p25 signals if you turn on CTCSS/DCS Tone Search)....
Turned it off and now it's decoding P25 in custom search such a simple fix!!!!!
CTCSS/DCS SEARCH ON
REPEATER FIND OFF
SET MODULATION AUTO
SET ATTENUATOR OFF
DATA SKIP OFF
ADJUST P25 level AUTO
CLOSE CALL BANDS ON[/quote]
Hi all while doing a bit of updating on computer for the scanner whith the Usad program. I noticed in the general search options under CTCSS/DCS Tone Search!!
( Scanner will not detect or decode p25 signals if you turn on CTCSS/DCS Tone Search)....
Turned it off and now it's decoding P25 in custom search such a simple fix!!!!!
Thanks sw sydney scanner. Using UBCD396T
Re: Ubc396t p25
if you have ctcss/dcs search on, the scanner thinks its looking for an analogue signal
Happily Scanning Since 1983